Posts Tagged ‘Green Builders’

There are two ways that windows help in heating and cooling – by preventing heat loss from the room, and by taking in heat from the outside. The former is measured by a window’s U-Factor and the latter by SHGC. U-Factor measures how much heat is lost through the window. The actual math gets quite complicated – U-Factor tells you how much heat is lost in one hour for one square foot at a certain temperature. A low U-Factor value (usually of 0.35 or lesser) means less loss and thus better insulation. Conversely, some windows may even mention an R-value, which is a measure of insulation. A low U-value corresponds to a high R-value.
SHGC is a value between 0-1. The lower the value, the less the amount of heat a window admits. Depending on the climate and your heating/cooling requirements you will need to pick a window with the right combination of SHGC and U-value. In cold climates, you want a U-value lesser than 0.35 combined with a high SHGC of around 0.60 or higher. This will considerable reduce the load on your heating system. For warm climates, you want the opposite – a low SHGC of less than 0.40 with a high U-value.
Does this mean you will have to change windows to match the seasons? Not necessarily. A metallic oxide layer (called a low E coating) applied on the outside keep the heat out, lowering the SHGC and when applied on the inside decreases the U-value. Even tints work well, though they only reduce the SHGC value.
Does material matter? Very much so, windows made of wood are not very good on insulation, while vinyl and fibreglass frames have the lowest U-values. Metal should be your last option when looking for insulation.

1. Adaptability: GHP can be used in a variety of climates and conditions. With air-source pumps, the general external temperature matters quite a bit. However, regardless of surface temperature, the temperature beneath the earth’s surface remains more or less warm, constantly. This makes it possible to use GHP in different geographical regions with different temperatures. Add to this, there are four different types of GHP installations available, depending on different soil, climate and installation costs. The local installer will be able to guide you to the best option for you.
2. High Efficiency: Because the earth’s temperature is more or less constant, GHP provide you with better heating cooling without having to create any heat in the first place. For moving heat, GHPs use only 50-75% of the electricity used by other heat pumps. This makes them extremely efficient, with a rate of 300-400%. They’re also very efficient at controlling humidity, which works great for a wet weather like ours.
3. Durability: GHPs have no moving parts, and the parts are rarely exposed to weathering or destructive elements. As such, with a proper installation, the entire system can last up to 25 years (and certain parts up to 50)
4. GHPs are much quieter that other heat pumps, require less space and can be configured for use in a new home or old one. Plus, it is also possible to control the heat supply and therefore the temperature of different rooms with GHP.

There’s quite a fraction of people reading this series on LED lighting who will nod their heads in disagreement. You’ve probably heard from your friend’s that they are very-expensive, very-chic, or that LED installations go bonkers after a few months. The problem is not with LED. LED is one of the best lighting options for residences, when used correctly. An inexperienced electrician and incorrect buying decisions can do a lot of harm to the lighting of the house, to you and your pocket. Here’s what to bear in mind:
1. Buy the right type of LED for your requirements. There are low wattage LEDs, which will work on 1mA (very little) of electricity and there are also new High-Power, high wattage LED which will work on more than 1A (100+ mA) and produce over 1000 lumens. The low wattage ones are used singularly to create different effects, usually for decorative purposes. The high wattage ones are used in place of a light bulb, or used in an array to provide enough light for an entire room.
2. Both types of LED lighting have different requirements. Low wattage LEDs burn out very quickly if not used with the right kind of voltage. They require much less than what is available by default in homes. High wattage ones, on the other hand can work with what we have in homes but need adequate heat sinks that will absorb the extra heat they will produce. If heat sinks are damaged, the lighting will burn out in seconds.
3. LEDs are quite affected by ambient room temperature. Installing them into walls which are not properly ventilated or in rooms that tend to get warm affects their life expectancy, causing them to fade out faster.

The Eco Builders Guild \ South Sound Chapter has announced it will host the South Sound Green Tour on April 17th and 18th, 2010
The theme of the event will be Innovation – Education – Inspiration

It will be a community event to celebrate green innovations through education in sustainable building and inspired living.
This year’s tour will showcase the greenest homes and buildings in our area that incorporate significant use of solar or other renewable energies, new and reclaimed materials, low energy consumption and water conservation technologies, and sustainable design techniques.
Educational sessions will be held at various locations and feature real life topics on how to build and live greener. See our website for more details – www.SouthSoundGreenTour.com ( The site should be up and running by January 1, 2010

South Sound Green Tour is looking for participants and sponsors. If you are interested in either contact me at info@laupenhomes.com. After January we you will be able to contact us directly at SouthSoundGreenTour.com

If you’ve been to a house that was recently done up (in a rather fashionable manner) – you might have found a lot of small whitish lights used in places where the conventional bulbs and CFLs used to be. These tiny things are LED (Light Emitting Diodes) a new entrant in the field of home lighting.
LED is a certain type of lighting device which is being increasing used in homes for many reasons. Largely, they are used more for decorative purposes, but their efficiency and long-life as compared to other fluorescent and incandescent lamps have led to LED using lamps to be used as the main source of light in a house.
The main factor working in LED’s favour is its efficiency. Unlike regular bulbs and fluorescent lights, which waste almost 90% of the energy they consume in the form of heat, LED release very little heat, using up most of the energy to produce light. Thus, its input/output ratio is quite high, and typically LED’s last about 20,000 to 35,000 light hours (compared to CFLs which last 15,000-20,000 hours and incandescent bulbs which last about 1000-2000 hours). This makes them an extremely cost-effective option, when compared to other forms of lighting.
To add to this, LED is available in a variety of colours and can be used very effectively for home decor. Also, LED is a point source of light. Which means if LED lighting is recessed into a wall, all the light it emits will go straight ahead into the room? When incandescent bulbs are recessed, only a fraction of the light will actually make it into the room.